耐電壓介電擊穿電氣強度試驗儀(bdjc-30kv)

耐電壓介電擊穿電氣強度試驗儀滿足標準：
儀器依據以下標準中對擊穿電壓部分的要求制造
GB/T 1408-2006  
GB/T1695-2005  
GB/T3333  
HG/T 3330 
GB12656  
ASTM D149 

儀器特點：
1、本儀器在試驗過程中可對升壓擊穿過程繪制實時曲線，每次試驗的升壓曲線都由不同顏色構成，試驗結束后可疊加對比材料的試驗數據重復性。
2、可以隨時調取當前及歷史試驗數據進行查看，編輯及修改參數。
3、試驗過程中可以隨時修改試驗條件及存儲路徑及自動存儲試驗結果。
4、試驗過程中，可隨時通過軟件決定本次試驗是否有效，方便篩選試驗結果。
5、可設置操作口令，做到專機專人操作，避免無關人員誤操作。

試驗方法

絕緣材料電氣強度試驗方法
硫化橡膠工頻電壓擊穿強度和耐電壓強度試驗 
電纜紙工頻電壓擊穿試驗方法 
絕緣漆漆膜擊穿強度測定法 
電容器紙工頻電壓擊穿試驗方法
固體電絕緣材料在工業電源頻率下的介電擊穿電壓和介電強度的試驗方法

結構特點：
   電壓擊穿試驗儀采用立式箱體結構，極大的節省試驗室內占地空間，地腳采用滑輪結構，方便移動和擺放，避免同類廠家生產的臥式設備，安放時需要另配安裝臺的情況，占地空間大，移動不方便等缺點。本產品采用直流伺服電機加載減速機構，保證了標準里面關于極慢速試驗和極快速試驗的要求，保證用戶可以自由選擇升壓速率。

主要技術要求：
1、設備輸入電壓： 交流 100KV (普通試驗室電源均可兼容)；
2、試驗電壓方式： 交流 0--100 KV；
                  直流 0--100 KV；
3、電器容量：10KVA；
4、試驗方法：0-100KV全量程可調(采用高精度電壓采樣器件)；
5、擊穿及耐壓試驗升壓速率：
0.1 KV/S 
0.2 KV/S
0.5 KV/S
1.5 KV/S
  2 KV/S
2.5 KV/S
3.0 KV/S(此項滿足標準里面極快速升壓試驗要求)；
6、試驗方式：
           直流試驗：1、勻速升壓  2、階梯升壓  3、耐壓試驗
           交流試驗：1、勻速升壓  2、階梯升壓  3、耐壓試驗
注：根據不同行業的標準，我們可以根據用戶的要求，依據貴行業標準，為您定制行業標準所需的特殊測試功能。
7、過電流保護裝置應有足夠靈敏度以保證試樣擊穿時在0.1S內切斷電源。
8、漏電電流選擇：1—100 mA可由計算機軟件自由進行設定。
9、本儀器采用無觸點原件勻速調壓方式(淘汰產品中機械傳動升壓方式)。
10、支持短時間內短路試驗要求。
11、一次試驗可以做5個試樣。
12、電壓測量誤差： ≤2％。
13、試驗電壓連續可調：0-100 KV
14、耐壓時間設定：0-6小時(可通過軟件連續設定)。
15、主機尺寸：1500mm*1200mm*1600mm（長寬高）。
16、主機重量：約200KG。
17、九級安全防護措施： 
(1) 超壓保護
(2)試驗過流保護 
(3)試驗短路保護
(4)安全門開啟保護
(5)軟件誤操作保護
(6)零電壓復位保護
(7)試驗結束放電保護
(8)獨立保護接地
(9)試驗完成后電磁放電

主要配置：

（采用國內或進口配件）
1、 試驗主機一臺
2、 10萬伏電壓擊穿試驗儀高壓發生器一臺
3、全自動微電腦電壓調壓裝置一套(串口方式)
4、步進電機一臺
5、控制系統一套
6、電壓及電流采集模塊一套
7、過流保護裝置一套
8、 試驗用電極 ￠25mm兩個 ￠75mm一個(可根據材料定制)
9、 試驗用油盒一只：材質為有機玻璃
10、放電棒一支（使用方法：試驗結束，電機歸位后關掉電源開關，拿出放電棒，拉直伸縮桿，將接地夾另一頭插入放電幫金屬探頭插孔中，然后將接地夾夾到儀器接地端上，手握絕緣手柄，打開試驗箱玻璃門，用金屬探頭接觸高壓頭即變壓器端。 注意：在每次試驗完成后拿出樣品前都要事先*放電，在放電時，在放電點接觸停留時間超過2秒。）
11、電壓擊穿計算機測控軟件一套
12、計算機一臺 
13、彩色噴墨打印機一臺
14、*計量鑒定質檢證書一份
15、產品使用說明書一份
16、數據線一套
17、合格證一份 
 

        常規型號：

       BDJC-10KV
       BDJC-20KV
       BDJC-50KV
       BDJC-100KV
       BDJC-150KV

北京北廣精儀儀器設備有限公司

*的電性能檢測產品供應商

Meet the standard:

Instruments according to the requirements of the following standards for the breakdown of the manufacturing
1408-2006 GB/T
GB/T1695-2005
GB/T3333
HG/T 3330
GB12656
D149 ASTM
Instrument characteristics:
1, the instrument in the test process can be used to draw real-time curve of the breakdown process, each test of the boost curve by different color composition, after the end of the test can be superimposed on the test data repeatability of the data.
2, can obtain the current and historical test data to view, edit and modify the parameters.
3, the test process can be modified at any time test conditions and storage path and automatic storage test results.
4, the test process, may at any time through the software to determine whether the test is effective, convenient screening test results.
5, can be set to operate the password, so that the special plane operation, to avoid irrelevant personnel misuse.
test method
Test methods for electrical strength of insulating materials
Power frequency voltage breakdown strength and voltage endurance test of vulcanized rubber
Test method for power frequency voltage breakdown of cable paper
Determination of breakdown strength of insulating paint film
Test method for power frequency voltage breakdown of capacitor paper
Standard Test Method for dielectric breakdown voltage and dielectric strength of solid electrical insulating materials at industrial power frequencies
Structure characteristics:
Voltage breakdown testing instrument adopts a vertical enclosure structure, greatly saves the space of indoor test, anchor the pulley structure, easy to move and placed, avoid similar manufacturers horizontal equipment, placed need with installation and, occupying a large area of space, do not move easily shortcomings. This product adopts the DC servo motor to load and speed reduction mechanism, which ensures the latest requirements of the latest standards, the latest requirements of the extremely slow test and very fast test, to ensure that users can freely choose the booster rate.
Main technical requirements:
1, equipment input voltage: AC 100KV (common test room power supply can be compatible);
2, test voltage mode: AC KV 0--100;
DC KV 0--100;
3, electrical capacity: 10KVA;
4, test method: 0-100KV full range adjustable (using high-precision voltage sampling device);
5, breakdown and pressure test boost rate:
0.1 KV/S
0.2 KV/S
0.5 KV/S
1.5 KV/S
2 KV/S
2.5 KV/S
3 KV/S (this is to meet the latest standard inside a very fast boost test requirements);
6, test methods:
DC test: 1, uniform step up 2, step up 3, pressure test
AC test: 1, uniform step up 2, step up 3, pressure test
Note: according to the standards of different industries, we can according to the requirements of users, according to your industry standards, for your custom industry standards required for the special test function.
7, over current protection devices should have sufficient sensitivity to ensure that the sample breakdown in the 0.1S cut off the power supply.
8, leakage current choice: 100 - 1 mA can be set by the computer software free.
9, the instrument adopts no contact original uniform pressure adjustment mode (the elimination of mechanical transmission in the product boost mode).
10, support short time short circuit test request.
11, a test can be done 5 samples.
12, voltage measurement error is less than 2%.
13, the test voltage can be adjusted continuously: KV 0-100
14, time setting: 0-6 hours (can be set through the software).
15, host size: 1500mm*1200mm*1600mm (length width height).
16, the host weight: about 200KG.
17, nine level security measures:
(1) overpressure protection
(2) test of over current protection
(3) test short circuit protection
(4) safety door opening protection
(5) software error protection
(6) zero voltage reset protection
(7) the end of the discharge protection test
(8) independent protection of ground
(9) after the test is completed, the electromagnetic discharge
Main configuration:
(use of domestic or imported accessories)
1, a test host
2, 10 kV voltage breakdown tester, a high voltage generator
3, fully automatic microcomputer voltage regulator device (serial mode)
4, stepper motor
5, a set of control system
6, voltage and current acquisition module set
7, over current protection device set
8, test of two electrode 25mm Phi 75mm a (according to the material can be customized)
9, test oil box one: material for organic glass
10, discharging rod a (using the method: the end of the experiment, motor homing after turning off the power switch, out of the discharging rod, straighten escopic rod, grounding clip on the other end into the discharge for metal probe insertion in, then the grounding clip clip to the instrument grounding end on, holding an insulation handle. And opened the door of the test box of glass, high head the transformer end in contact with a metal probe. Note: before each test is completed, the sample must be fully discharged in advance, in the discharge, the discharge point of contact for more than 2 seconds.
11, voltage breakdown computer control software set
12, a computer
13, color inkjet printer
14, the national level measurement and identification of a quality certificate
15, a copy of the instructions of the product
16, a set of data lines
17, a certificate of qualification